Forrest CM10806105 Chopmaster 10-Inch 80 Tooth ATBR Miter and Radial Saw Blade with 5/8-Inch Arbor

Forrest CM10806105 Chopmaster 10-Inch 80 Tooth ATBR Miter and Radial Saw Blade with 5/8-Inch Arbor Review

Forrest CM10806105 Chopmaster 10-Inch 80 Tooth ATBR Miter and Radial Saw Blade with 5/8-Inch Arbor Feature

• 20° Face Hook for easy feed
• DOUBLE HARD and 40% STRONGER C-4 CARBIDE will give up to 300% longer life between sharpenings.
• Ends second-step finishing (jointing and sanding not required).
• Buy and sharpen ONE blade instead of 3, (24T Rip, 50T Combination, 80T Crosscut).
• Ends cutting 1/16" oversize to allow for RESURFACING

Maintain maximum stability for the best cut with a Forrest Chopmaster Saw Blade. Specially designed for sliding compound miter and radial-arm saws, grabbing and throwing of scrap cutoffs has been minimized with this design.This blade has a heavier than normal steel plate and a negative face hook. Its made with double-hard C-4 submicron carbide for up to 300 longer life. Each blade is hand-straightened to a runout of .001"/.002" for maximum cut quality The tooth style (4 points and flat) produces steady, clean cuts with no bottom splintering. Youll be delighted by the extra smooth, tight cuts youll get with this blade. The 10" blade has a 7/64" kerf and 5/8" arbor hole.

Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB .125 Kerf Saw Blade with 5/8-Inch Arbor

Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB .125 Kerf Saw Blade with 5/8-Inch Arbor Review

Forrest WW10407125 Woodworker II 10-Inch 40 Tooth ATB .125 Kerf Saw Blade with 5/8-Inch Arbor Feature

• This kerf saw saves 1/3 on wood loss for each cut
• Feeds easily when used for moderate rips and crosscuts on a table saw
• Reduces jump in for better pull control
• Eliminates bottom splintering on radial crosscuts
• The new 30-degree ATB tooth style stops the blade totally

Forrest Premium Carbide Saw Blades cut cleaner, more efficiently, and last longer between sharpenings than almost any other blade.They feature super hard, long life micro-grain carbide teeth on laser-cut plates that are hand-straightened to a maximum runout of .002". These top quality blades rip and crosscut super smooth and tear-out free. All are 10" diameter and fit 5/8" arbors. Made in the USA, the Woodworker II ATB blade is the most popular for general table saw use. It has a plate thickness of .090, and the kerf is 1/8". If most of your cutting is stock 1-1/2" or thicker, Forrest recommends its 30-tooth blade (#85N53).

Forrest WW10407100 Woodworker II 10-Inch 40-tooth ATB .100 Kerf Saw Blade with 5/8-Inch Arbor

Forrest WW10407100 Woodworker II 10-Inch 40-tooth ATB .100 Kerf Saw Blade with 5/8-Inch Arbor Review

Forrest WW10407100 Woodworker II 10-Inch 40-tooth ATB .100 Kerf Saw Blade with 5/8-Inch Arbor Feature

• Saves 1/3 wood loss on each cut.
• Feeds easily when used for moderate rips and crosscuts on a table saw.
• Reduces "JUMP IN" for better "PULL-CONTROL."
• Eliminates bottom splintering on RADIAL CROSSCUTS.
• With new 30° ATB tooth style this blade stops totally, ALL bottom and top splintering on ply veneers on both radial and table saw machines

Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Forrest Woodworker 1 Saw Blade For Radial and Table Saws. These trim and cross-cut ALL PURPOSE blades give scratch-free POLISHED cuts on wood, RIP or CROSSCUT, up to 2' thick. They have a 30° Alternate Top Bevel with a 5° Face Hook on 10' diameters and smaller.Saves 1/3 wood loss on each cut.Feeds easily when used for moderate rips and crosscuts on a table saw.Reduces 'JUMP IN' for better 'PULL-CONTROL.'Eliminates bottom splintering on RADIAL CROSSCUTS.With new 30�� ATB tooth style this blade stops totally, ALL bottom and top splintering on ply veneers on both radial and table saw machines

Forrest CM12806115 Chopmaster 12-Inch 80-tooth ATB Miter Saw Blade with 1-Inch Arbor

Forrest CM12806115 Chopmaster 12-Inch 80-tooth ATB Miter Saw Blade with 1-Inch Arbor Review

Forrest CM12806115 Chopmaster 12-Inch 80-tooth ATB Miter Saw Blade with 1-Inch Arbor Feature

• Saves 1/3 wood loss on each cut.
• Feeds easily when used for moderate rips and crosscuts on a table saw.
• Reduces "JUMP IN" for better "PULL-CONTROL."
• Eliminates bottom splintering on RADIAL CROSSCUTS.
• With new 30° ATB tooth style this blade stops totally, ALL bottom and top splintering on ply veneers on both radial and table saw machines

We're rarely speechless around here, but after bringing this blade down through a gorgeous piece of maple, it nearly happened. We knew that Forrest makes some of the best blades on the planet, but we truly weren't prepared for the gorgeous cut we got with this blade.

On the back side of plywood, we had zero tearout. When we cut a length of 8/4 oak, it felt like a hot knife through butter, and the result was too good to be believed: smooth as glass, completely free of circle marks of any kind, and it looked like it had been sanded already - cut after cut after cut.

You can pick up a miter saw blade for a tenth of this price, of course. It will cut. But it won't cut like this. And it won't last as long as this blade will, not by a long shot. Because it's made of double-hard C-4 carbide, it holds it edge for what seems like forever, and it resharpens beautifully.

Forrest spends a good deal of time on each blade, ensuring that it's as straight as can be, and that's part of what you're paying for. If you spent good money on a decent miter saw, you owe it to yourself to put this blade on it. After parting with your money, you will never regret buying this blade. --Kris Jensen-Van Heste Maintain maximum stability for the best cut with a Forrest Chopmaster Saw Blade. Specially designed for sliding compound miter and radial-arm saws, grabbing and throwing of scrap cutoffs has been minimized with this design. This blade has a heavier than normal steel plate and a negative face hook. Its made with double-hard C-4 submicron carbide for up to 300 longer life. Each blade is hand-straightened to a runout of .001/.002 for maximum cut quality. The tooth style (4 points and flat) produces steady, clean cuts with no bottom splintering. Youll be delighted by the extra smooth, tight cuts youll get with this blade. The 12" blade has a 1/8" kerf and 1" arbor hole.

Forrest WW10307125 Woodworker II 10-Inch, 30 Tooth, 5/8-Inch Arbor, 1/8-Inch Kerf Circular Saw Blade

Forrest WW10307125 Woodworker II 10-Inch, 30 Tooth, 5/8-Inch Arbor, 1/8-Inch Kerf Circular Saw Blade Review

Forrest WW10307125 Woodworker II 10-Inch, 30 Tooth, 5/8-Inch Arbor, 1/8-Inch Kerf Circular Saw Blade Feature

• 10-inch circular saw blade with a 5/8-inch arbor, 1/8-inch kerf, and a 30-tooth design
• Cuts in all directions- rip, cross-cut, miter, any depth; cuts all sized grooves 1/4 inch through 29/32-inch increments
• Super-hard carbide gives up to 300% longer life; works especially well on plywoods and abrasive particle-boards
• Set of plastic adjusting shims included
• Weighs 2.3 pounds shipped

This 10-inch Forrest circular saw blade offers a superior cut that leaves a rip-cut saw edge that's as smooth as if it had been sanded, and a cross-cut edge that's almost mark-free. This blade runs very quietly, and the backside tear-out in plywood is negligible. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the manufacturing process.

Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind its blades by offering a sharpening service that brings blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new.

The No-Melt carbide-tipped saw blade is especially designed for cutting single or multiple stacked sheets of plastic without chipping or melting these materials. No-Melt blades are particularly suitable for acrylics, delrins, ABS (Coycolac), styrenes, PVC, and both high and low-melt nylons. Specially engineered side clearances on the carbide teeth significantly reduce -- and in many cases, totally eliminate -- any formation of melted burrs of buildup of residue on cross-sawn sections of plastic materials. Made with double-hard and 40 percent stronger C4 carbide, so you can expect 50 to 300 percent longer life between sharpenings. Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. The NO-MELT carbide-tipped saw blade is especially designed for cutting single or multiple stacked sheets of plastic without chipping or melting these materials. NO-MELT blades are particularly suitable for acrylics, delrins, ABS (Coycolac), styrenes, PVC, and both high and low melt nylons. Specially engineered side clearances on the carbide teeth significantly reduced and in many cases, totally eliminate any formation of melted burrs of buildup of residue on cross-sawn sections of plastic materials. Made with DOUBLE-HARD and 40% stronger #C4 Carbide. 50% to 300% Longer Life Between Sharpenings, Reduced Yearly Sharpening Costs, Less Machine Downtime, Improved Labor Efficiency, Inventory Savings -- Fewer Blades Required.10-inch circular saw blade with a 5/8-inch arbor, 1/8-inch kerf, and a 30-tooth designCuts in all directions- rip, cross-cut, miter, any depth; cuts all sized grooves 1/4 inch through 29/32-inch incrementsSuper-hard carbide gives up to 300% longer life; works especially well on plywoods and abrasive particle-boardsSet of plastic adjusting shims includedWeighs 2.3 pounds shipped

Forrest MM10106 Miter Master 10-Inch 100 Tooth 5/8-Inch Arbor .105-Inch Kerf Wood Cutting Circular Saw Blade

Forrest MM10106 Miter Master 10-Inch 100 Tooth 5/8-Inch Arbor .105-Inch Kerf Wood Cutting Circular Saw Blade Review

Forrest MM10106 Miter Master 10-Inch 100 Tooth 5/8-Inch Arbor .105-Inch Kerf Wood Cutting Circular Saw Blade Feature

• No splinters cross-cutting oak, ply veneers and melamine
• Cuts in all directions- rip, cross-cut, miter, any depth.
• Cuts all sized grooves 1/4" through 29/32" increments. (Set of plastic adjusting shims also included)
• Super-hard carbide gives up to 300% longer life, especially good on plywoods and abrasive particle-boards.

Forrest's blades offer a superior cut that leaves a rip-cut saw edge that is as smooth as if it had been sanded, and a cross-cut edge that is almost mark-free. The blades run very quietly, and backside tearout in plywood is negligible. Each blade is virtually hand-made. The plate is hand-tensioned (up to 15 minutes per blade), superior C-4 carbide teeth are hand-brazed to the plate, and the blade is straightened and restraightened multiple times throughout the process. Think of a Forrest blade as a tool in your shop, not an accessory. Forrest stands behind it's blades by offering a sharpening service that bring blades back to the exact tolerances offered in a new blade. And this same exacting service is available for other manufacturer's blades as well, so they should come back better than new. Recommended for: thin, low pressure, two-sided laminates, plywood & fine cross cutting on all woods. Eliminates need for a small scoring saw blade on table saw work. The 40° points slice through thin bottom layers with no tears or chips. Reduced yearly sharpening costs - less machine downtime.No splinters cross-cutting oak, ply veneers and melamineCuts in all directions- rip, cross-cut, miter, any depth.Cuts all sized grooves 1/4' through 29/32' increments. (Set of plastic adjusting shims also included)Super-hard carbide gives up to 300% longer life, especially good on plywoods and abrasive particle-boards.